Hirschmann Joint two-wire passive programmable control 4-20mA loop digital display meter:SY LED5
Hirschmann Joint two-wire passive programmable control 4-20mA loop digital display meter:SY LED5
Features:
● Low cost modular design, easy to install in use.
●2-wire passive operation mode, no auxiliary power.
●High measuring accuracy, 4-digit display, ±2 digits.
●LED display panel, adapt to different lightness requirements.
● Small size, dimension 65.4X45.3x46.5mm (LxWxH)
●Industrial operating temp.: -25℃～70℃, high reliability. |
Applications:
● Sensor, transmitter operating status display.
● Industrial equipment monitoring or remote control.
● Oil, chemical, environmental system monitoring.
● Temperature, pressure, flow, level signal monitoring and display.
● PLC, DCS system operation data acquisition and display.
● Developing meters & instruments, medical devices, industrial equipment. |
Introduction:
SunYuan SY LED5 Low cost Hersmann Joint 4-Digit 2-wire Passive Intelligent 4-20mA Current LED Display Meter input is passive signal, output 2 lines can be connected to the transmitter 4-20mA loop in serial GDM3009 socket and plug is designed in the display meter. It can display decimal number correspondingly based on the settings through 4-20mA analog signal in the loop. SY LED5 series Display Meter is designed on the base of 2-wire passive mode; it measures the electric signal which can be used as the input signal and the operating power supply of the display meter. The meter operates without power supply, low cost, high precision, small size, so it is very convenience to use. The traditional analog display meter uses potentiometer to do adjust parameters, it is not convenience and very easy to be effected by temperature. Compared with traditional analog display meter, the LED display meter is set by 2 buttons and controlled by CPU, the zero, span, decimal, alarm, delay time, etc parameters can be set by user, it is much more flexible and convenient in use. That display meter has use LED display board and operates in continuous voltage, in the 4-20mA measuring range, the display digits are in equal and stable brightness. It has anti-reverse connection, over-current protection and is widely applied in industrial site, oil, environment monitor, temperature, pressure, flow, level measuring, etc site and fields. In the actual applications, the LED display meter converts temperature, pressure, flow, level, etc physical quantity into 4-20ma signal, then connect with SY LED2 display meter, it displays the temperature, pressure, flow, and level, etc physical quantity to provide convenience for user to monitor and control the industrial site.
SYLED5 Display Meter is used to measure 4-20mA DC current signal, it does not need power supply and get power from 4-20ma current loop. The digits displayed are not the actual current value, it is the preset value of 4mA, 20mA, and displays the current valued measured based on the preset value in linearity method. E.g.: 4mA is set to 0, 20mA is set to 8000, then if input is 8mA, the meter displays 2000, input is 12mA, the meter displays 4000. If 4mA is set to 1000, 20mA is set to -1000, when input is 12mA, the meter displays 0, input is 16mA, the meter displays -500. The max. display range is 9999, that is four digits, min. Display range is -1999.
SY LED5 Digit Display Meter has alarm function and 2-channel isolated switch quantity output to realize timely display, controlling and alarm. The alarm function is realized by programming, and there are 2 pieces of PC452 land pad is reserved for customer use when alarm function is required. The display meter has 2 alarm points which can be set in up and down directions. The alarm target of the alarm point is the digit displayed, when there is alarm, the last decimal of the LED Meter is flashing, and the alarm signal is output through terminal which can drive the Optocoupler.
SY LED2 Dimension: 65.4×45.3x46.5mm, LxWxH , the external shell is made of flame-retardant plastic. The meter is mainly used to display the sensors or transmitter or controlling meters signals.
Note:
1. Do not connect input signal (current polarity) in reverse, otherwise it may damage the display meter.
2. Input current signal usually should be no more than 25mA, if input is up to 100mA, there is irreparable damages. In testing it with the current loop, 200Ω or larger resistance should be added in series in the loop to protect the display meters.
3. Do not use it in humid and corrosive environment, otherwise it will reduce the life-span or cause irreparable damage.
SY LED5 Display Meter Technical Parameters:
1. Using conditions
⑴Current: Rated range 3～22mA
Limited range: less than 100 mA
⑵Temperature range: Rated range: -20℃～60℃
Limited range: -40℃～70℃
⑶Relative humidity 20%～90%RH
⑷Shock & Vibration: meet industrial electronics environmental test II meters’ requirements.
2. Panel display method:
Black LED digits and decimal display, digits height 9.3mm (0.37inch)
3. Four-digit Display Meter Setting Range:
(1) 4mA:－1999～9999
(2) 20mA: －1999～9999
4. Voltage drop:
Voltage drop ≤3.2V, with over-current protection.
5. Polarity conversion: If lower than the zero limit, the meter display “-”, if higher than the zero limit, no polarity mark display.
6. Accuracy: linearity offset ±2 digits (to 2000 rated value).
7. Temperature error:≤50PPM／℃
8. Over-range display: “oHH” or “oLL”.
9. External Dimension:65.4x45.3x46.52mm Flame retardant housing shell.
Sunyuan Technology SY Series Intelligent Digital Display
Sunyuan Technology the newest developed SY LED / SY LCD series,with low cost, small size isolation transmitter 4-20mA two-wire passive intelligent display control instrument, dedicated to sensors and isolation transmitters |isolation amplifiers | PLC | DCS, etc.Isolated transmission of analog signals and intelligent display control. These LED or LCD four-bit high precision intelligent digital display meters use the principle of two-wire passive digital adjustment. The electrical signal passed through the digital measuring circuit is used as the input signal of the display meter and also the working power of the display meter. This two-wire passive type of operation eliminates the need for additional auxiliary power supplies. It is easy to connect in industrial field and has reverse protection and overcurrent protection. Products are widely used in industrial intelligent control, instrumentation intelligence, petrochemical, environmental monitoring, rail transit, electric vehicles, smart home, fire safety, mining monitoring and other industries on temperature, pressure, flow, liquid level, displacement, speed, frequency Monitoring of physical quantity control points. In industrial control systems, most applications use a variety of related sensors to convert physical quantities such as temperature, pressure, and displacement into 4-20 mA electrical signals, and intelligent digital display displays these electrical signals in real time for human convenience. Carry out all kinds of monitoring and control
Adopt product combination picture with "Sunyuan Intelligent Display Control Software
Adopt the related products data of design (SunYuan Intelligent display controll software)
一、Intelligent digital display with built-in intelligent display control software
1、Low cost and small size intelligent digital meter: SY LED1 / SY LCD1 type
SY LED1 detail technical information：
http://www.szsunyuan.com/index.phpm=content&c=index&a=show&catid=57&id=21
2、Panel embedded intelligent digital display：SY LED2 type
detail technical information：
http://www.szsunyuan.com/index.phpm=content&c=index&a=show&catid=57&id=5
3、Two-wire intelligent digital meter：SY LED3 / SY LCD3 type
SY LED3 type detail technical information：
http://www.szsunyuan.com/index.phpm=content&c=index&a=show&catid=57&id=118
4、Isolation transmitter embedded intelligent digital display：SY LED4 / SY LCD4 type
SY LED4 type detail technical information：
http://www.szsunyuan.com/index.phpm=content&c=index&a=show&catid=57&id=119
5、Hessmann isolation transmitter intelligent digital display：SY LED5 / SY LCD5 type
SY LED5 type detail technical information：
http://www.szsunyuan.com/index.phpm=content&c=index&a=show&catid=57&id=120
二、Built-in intelligent display control software---two-wire passive type intelligent: signal isolator / isolation transmitter / isolation distributor
1、Passive two-wire 4-20mA intelligent monitoring isolator：DIN 1X1 ISO 4-20mA（LED1）
Detail technical information：
http://www.szsunyuan.com/index.phpm=content&c=index&a=show&catid=59&id=44
3、Two-wire passive 4-20mA loop feed display control transmitter：DIN 1X1 ISO 4-20mA-F（LED）
detail technical information：
http://www.szsunyuan.com/index.phpm=content&c=index&a=show&catid=59&id=123
4、Two-wire passive type 4-20mA isolated to voltage signal display control instrument：DIN 1X1 ISO 4-20mA-O（LED1）
detail technical information：
http://www.szsunyuan.com/index.phpm=content&c=index&a=show&catid=59&id=122
5、Two-wire AC signal (AC/DC) feed isolation display control smart meter：DIN 1X1 ISO NNAC-O1（LED1）
detail technical information：
http://www.szsunyuan.com/index.phpm=content&c=index&a=show&catid=59&id=126
