6KV high isolation analog signal display control transmitter:DIN 1X1 ISO EMH (LED1)
Product Category: Active Intelligent Isolation Amplifier with LED Display
Input: 4-20mA,0-20mA,0-5V,0-10V Output: 0-10V,0-20mA
Power: -- Isolation Voltage: 6000VDC
Package: DIN35 Traffic Watch: times
Remarks: 6KV high isolation analog signal display control transmitter
Product Description
6KV high isolation analog signal display control transmitter:DIN 1X1 ISO EMH (LED1)

typical application :
● High-speed rail, subway 750V/1500V track voltage isolation monitoring
● Grid equipment operation signal detection, isolation and long-distance transmission
● Grid transformer safe operation detection and monitoring
● Power instrumentation and sensor signal transmission and reception and monitoring
● High-voltage inverter signal remote anti-interference and distortion-free transmission
● Power monitoring, medical equipment isolation barrier
● Analog signal ground line interference suppression and high isolation acquisition
● PLC, DCS field analog signal high isolation detection
● Industrial high-voltage equipment operation measurement, monitoring and remote control
● Oil, chemical, environmental protection, mining system control point monitoring
● Temperature, pressure, flow, liquid level signal visual display monitoring
● Sensor and transmitter working status display and control
Features :
● Visual display of online input or output signal values ​​for on-site inspection and operation
● High-precision four-digit LED digital display with ±2 words at the end of the display resolution
● Programmable setting of two-way lower limit isolated switch alarm signal output
● Accuracy class: 0.1, 0.2, 0.5, non-linearity <0.2% of full scale
● Built-in multiple protection circuits, no external components required, zero point gain adjustment
● Between auxiliary power supply, analog input and output: 6000VDC three isolation
● Auxiliary power supply: single power supply mode such as 5V, 12V, 24VDC, 220VAC
● 0-75mV//0-5V/0-10V/0-1mA/0-20mA/4-20mA analog signal
Isolation, amplification, and display and control
● Industrial temperature range: -25 ~ +70 °C
● Low cost, small size standard DIN 35 rail mounting method
● EMC interference requirements must be added to the electromagnetic interference suppression circuit and shielding measures

The SunYuan DIN 1X1 ISOEMH (LED1) series is intelligently designed with features not found in traditional products. The analog signal can be isolated and transmitted only by a single power supply, and displayed in decimal digital quantities according to the set range. The traditional embedded analog display meter is adjusted by a potentiometer, and the adjustment parameters are single, inflexible, and greatly affected by temperature. Compared with the traditional analog display table, this intelligent digital display table is operated by two key combinations and controlled by the central processing unit CPU, which can realize setting of various parameters such as zero point, full scale, decimal point, alarm and delay. , with strong flexibility and practicality. The digital display adopts an LED display panel and has reverse and overcurrent protection functions. Products are widely used in high-speed rail, subway 750V/1500V track voltage isolation monitoring, power instrumentation and sensor signal transmission and reception and monitoring, high-voltage inverter signal remote anti-interference and distortion-free transmission, grid transformer equipment operation signal detection, isolation and long-distance transmission, power monitoring , medical equipment isolation barrier.
         DIN 1X1 ISO EMH (LED1) series of intelligent high-isolation transmitters are display control transmitters that amplify, convert, and convert analog voltage or current signals into high precision and linearity. The product integrates isolation, display, alarm control and transmission. It contains a set of high efficiency and multi-isolated DC/DC power conversion circuit, signal modulation and demodulation circuit, signal coupling isolation conversion circuit, display and alarm control circuit. Especially suitable for: 0-75mV/0-5V/0-10V/0-1mA/0-20mA/4-20mA and other analog unregulated isolation amplification transmission, display and control. The product adopts a low-cost solution of magnetoelectric coupling, and is mainly used in applications where there is no special requirement for EMC (electromagnetic interference). The internal integrated process structure and new technology isolation measures enable the device to achieve: auxiliary power supply, signal input and output 6000VDC three isolation. And can meet the industrial requirements of wide temperature, humidity, vibration environment. Intelligent design of the new high-isolation transmitter series products built-in reverse connection, overload, anti-surge and other protection circuits, no external components, zero-point gain adjustment, standard DIN35 rail installation, convenient for users to use on-site.
         DIN 1X1 ISOEMH (LED1) series of active intelligent isolation transmitters can directly isolate and convert analog signals, and have signal display and output alarm control functions. The embedded intelligent digital display meter is used to measure the transmission signal. The displayed digital value is not a direct output voltage or current measurement value, but a signal preset value. By setting the measured output zero point and full-scale voltage or current value relative to each other. These two preset values ​​are displayed linearly. For example: the transmission output 4-20mA, 4mA is set to 0, 20mA is set to 8000, then the meter will display 2000 when input 8mA, 4000 will be displayed when input 12mA; and if the 4mA is set to 1000, 20mA is set to - 1000, the table will display 0 when 12mA is input, and -500 will be displayed when 16mA is input. The maximum display range of the digital display is 9999, which is four digits; the minimum is -1999. Its alarm function with two isolated switch outputs can display, control and alarm on the spot. The two alarm points set have positive and negative alarm direction settings. The alarm object of the alarm point is for the display reading. The last decimal point of the LED panel flashes during the alarm, and the alarm information is isolated and output by the digital optocoupler. For products that need to set the alarm function, the upper or lower limit alarm value and alarm mode can be modified by the programmer. For detailed setting method, please refer to the “Display Table User's Manual” on the following page. Remark: The alarm signal is the OC gate (open collector) output. For the specific application, please refer to the [Alarm Output and Application] on the following page.

Product selection example:
Example 1, Input: 0-5V; Auxiliary power supply: 24VDC; Output: 4-20mA; Signal input/output/auxiliary power supply: 6KVDC high isolation; DIN35 rail mounting; LED display. Model: DIN 1X1 ISO EMH U1-P1-O1 (LED1)
Example 2, input: 4-20mA; auxiliary power supply: 24VDC; output: 4-20mA; signal input/output/auxiliary power supply: 6KVDC high isolation; DIN35 rail mounting; LED display. Model: DIN 1X1 ISO EMH A4-P1-O1 (LED1)
Example 3, input: 4-20mA; auxiliary power supply: 5VDC; output: 0-5V; signal input/output/auxiliary power supply: 6KVDC high isolation; DIN35 rail mounting; LED display. Model: DIN 1X1 ISO EMH A4-P3-O4 (LED1)

Product Pictures:

Alarm output and application:
1. The DC level signal generated by the two-way alarm signal in the main CPU chip is isolated and output by the optocoupler. The output low level indicates the alarm state, and the output high level is the non-alarm state.
2. Because the display controller is passive two-wire system, the minimum working current is 3mA, so the alarm signal is also very weak, the minimum is only 0.5mA. The signal is isolated by a phototransistor type photocoupler with a strong current spreading capability, and an open collector (OC gate) output is used. The output is connected to the pull-up voltage, and the current can be expanded up to 120mA. The principle of this phototransistor type photocoupler is shown in the figure below: the instrument signal is isolated by optocoupler, 9, 10 "1H /1L", 7, 8 "2L /2 H" wiring port is optocoupler OC gate The output end of the signal is connected to the external power supply circuit of the instrument, and further amplifies and energizes the alarm signal, and finally reaches an actuator that can drive the required sound, light, electricity, refrigeration, heating, and motor. 9, 10 "1H / 1L" is the first alarm output, 7, 8 "2L /2 H" is the second alarm output, "1H", "2H" connected to the phototransistor collector, "1L", "2L emitter.

3. Because of the limitation of the maximum current of the phototransistor Ic, its expansion and driving load capacity is limited. If the user needs more driving current, it can be used to drive relays, solenoid valves, stepping motors and other devices on site, and can externally connect the power expansion circuit. The power amplifier tube or servo circuit is subjected to current amplification and special processing.
Order selection instructions:
Please read the entire contents of this manual carefully before ordering to determine whether the product meets the user's on-site application and is correctly selected.
1. The factory default setting of this product is set to “0.0” by 4mA and “200.0” by 20 mA.
2. When ordering, the user should first put forward the display specification requirements. We will adjust the digital display meter before leaving the factory, which is convenient for users to use directly.
3. When ordering, please indicate the type and parameters of the access signal: AC, DC, resistance (displacement, potentiometer), bridge (pressure, weighing), etc.
Sunyuan Technology SY Series Intelligent Digital Display
Sunyuan Technology the newest developed SY LED / SY LCD series,with low cost, small size isolation transmitter 4-20mA two-wire passive intelligent display control instrument, dedicated to sensors and isolation transmitters |isolation amplifiers | PLC | DCS, etc.Isolated transmission of analog signals and intelligent display control. These LED or LCD four-bit high precision intelligent digital display meters use the principle of two-wire passive digital adjustment. The electrical signal passed through the digital measuring circuit is used as the input signal of the display meter and also the working power of the display meter. This two-wire passive type of operation eliminates the need for additional auxiliary power supplies. It is easy to connect in industrial field and has reverse protection and overcurrent protection. Products are widely used in industrial intelligent control, instrumentation intelligence, petrochemical, environmental monitoring, rail transit, electric vehicles, smart home, fire safety, mining monitoring and other industries on temperature, pressure, flow, liquid level, displacement, speed, frequency Monitoring of physical quantity control points. In industrial control systems, most applications use a variety of related sensors to convert physical quantities such as temperature, pressure, and displacement into 4-20 mA electrical signals, and intelligent digital display displays these electrical signals in real time for human convenience. Carry out all kinds of monitoring and control

Adopt product combination picture with "Sunyuan Intelligent Display Control Software

Adopt the related products data of design (SunYuan Intelligent display controll software)
一、Intelligent digital display with built-in intelligent display control software
1、Low cost and small size intelligent digital meter: SY LED1 / SY LCD1 type
SY LED1 detail technical information:


2、Panel embedded intelligent digital display:SY LED2 type
detail technical information:


3、Two-wire intelligent digital meter:SY LED3 / SY LCD3 type
SY LED3 type detail technical information:


4、Isolation transmitter embedded intelligent digital display:SY LED4 / SY LCD4 type
SY LED4 type detail technical information:


5、Hessmann isolation transmitter intelligent digital display:SY LED5 / SY LCD5 type
SY LED5 type detail technical information:


二、Built-in intelligent display control software---two-wire passive type intelligent: signal isolator / isolation transmitter / isolation distributor
1、Passive two-wire 4-20mA intelligent monitoring isolator:DIN 1X1 ISO 4-20mA(LED1)
Detail technical information: 


3、Two-wire passive 4-20mA loop feed display control transmitter:DIN 1X1 ISO 4-20mA-F(LED) 
detail technical information: 


4、Two-wire passive type 4-20mA isolated to voltage signal display control instrument:DIN 1X1 ISO 4-20mA-O(LED1)
detail technical information:


5、Two-wire AC signal (AC/DC) feed isolation display control smart meter:DIN 1X1 ISO NNAC-O1(LED1)
detail technical information:
6、Potentiometer,electric bridge etc other voltage sensor signal conversion display control instrument:DIN 1X1 ISO V-4-20mA(LED1)
detail technical information: 


三、Built-in intelligent display control software---active intelligent: isolation amplifier / isolation transmitter / isolation distributor
1、Intelligent universal standard analog active transmitter: DIN 1X1 ISOEM (LED1) series
detail technical information:

2、Support differential input millivolt analog small signal distribution type display control transmitter: DIN 1X1 ISOEM-SD (LED1) series
detail technical information:

3、Two-wire passive sensor power distribution type display control isolation transmitter for input: DIN 1X1 ISOEM-S (LED1) series
detail technical information:


4、6000V high isolation analog signal display control transmitter: DIN 1X1 ISO EMH (LED1)
detail technical information:

四、Built-in intelligent display control software---sensor-specific intelligent: isolation amplifier / isolation transmitter / isolation converter
1、AC signal to direct current (AC/DC) display control transmitter: DIN 1X1 ISO AC-P-O (LED1) series
detail technical information:

2、Analog isolation to pulse frequency signal display control isolation transmitter: DIN 1X1 ISO U/A-P-F (LED1) series
Detailed technical information:

3、Sine wave, square wave to analog signal display control isolation transmitter: DIN 1X1 ISO (SY) F-P-O (LED1) series
detail technical information:


4、Electronic ruler, angular displacement signal display control isolation transmitter: DIN 1X1 ISO R-P-O (LED1) series
detail technical information:

5、Pt100/Cu50 RTD Signal Display Control Isolation Transmitter: DIN 1X1 ISO Z-W-P-O (LED1) Series
detail technical information:
6、AC true RMS signal to analog signal display control transmitter: DIN 1X1 ISO EM RMS-P-O (LED1) series
detail technical information:

7、PWM pulse width modulation signal isolation display control transmitter: DIN 1X1 ISO D-P-O-Q (LED1) series
detail technical information:

五、Built-in intelligent display control software---analog data collector (intelligent AD/DA converter)
1、2-channel analog AD acquisition display control isolation transmitter: ISO 4021 (LED1) series
detail technical information:

2、Bus RS232/485 isolated conversion 4-20mA display control module: ISO DA (LED1) series
detail technical information:



Related Data Sheets
Product Categories
Product Recommended
Copyright ©2002-2018 Sunyuan Corporation. All rights reserved. SHENZHEN SUNYUAN TECHNOLOGY CO., LTD. Address: 2nd Floor, Building#6, Dongyi Industrial Park, Zhonghuan Road, Minzhi St. Longhua New District, Shenzhen, 518109, China. Tel: +86-755-83100080 83100110 Fax : +86-755-83116652 Email: sy@sun-yuan.com